Staff Power Electronics Engineer Verified today

About the Role

CesiumAstro develops communication systems for satellites, UAVs, launch vehicles, and airborne platforms. The Skylark product line focuses on active phased array antennas (AESA) for terrestrial and airborne applications, including high-power ground terminals for missile defense and commercial airline and helicopter connectivity solutions.

What You Will Do

• Lead the development of power system architectures and derive power subsystem requirements.
• Design DC-DC power converters, power supplies, and power distribution systems ranging from a few watts to more than 20 kW in the 0.8 V to 400 V range.
• Design single-phase and three-phase AC-DC power supplies and power distribution systems ranging from a few kilowatts to more than 20 kW.
• Perform comprehensive analysis of AC-DC and DC-DC power supplies including worst-case circuit analysis (WCA), stress analysis, small signal modeling, failure modes and effects analysis (FMEA), reliability analysis, and power integrity analysis.
• Develop design verification test plans, requirement compliance matrices, system integration and qualification test plans, and production acceptance test plans for power converters and power supplies.
• Lead board bring-up and design verification testing of analog and power electronics circuits.
• Lead system integration, qualification campaigns, and production release of power supply modules and power systems.
• Mentor younger engineers and foster knowledge sharing.
• Lead a small team of power electronics engineers to drive project execution.

Minimum Qualifications

• Bachelor of Science (BS) degree or higher in Electrical Engineering from an accredited university.
• Minimum of 8 years of experience designing analog and power electronics.
• Experience with electrical power systems and subsystems, including power architecture development, power requirements definition, SWAP-C trade studies, converter topology selection, and power management and control blocks.
• Experience designing, testing, and qualifying single-phase and three-phase off-line AC-DC power supplies and DC-DC power supplies for industrial, airborne, or military systems.
• Knowledge of control theory and stability of power electronics, including experience characterizing control loops and impedances in the laboratory.
• Experience designing power filters for low noise outputs and power line electromagnetic compatibility (EMC).
• Experience developing design verification test plans, requirement compliance matrices, system integration and qualification test plans, and production acceptance test plans.
• Experience performing worst-case circuit analysis (WCA), stress analysis, failure modes and effects analysis (FMEA), and reliability analysis for power supplies.
• Extensive hands-on experience with testing and troubleshooting electronics and power converters using laboratory instruments such as oscilloscopes, impedance analyzers, spectrum analyzers, electronic loads, and signal generators.
• Experience with analysis and simulation tools such as SPICE, LTSPICE, SIMetrix/SIMPLIS, PLECS, Simulink, MATLAB, MathCAD, ANSYS Q3D and SiWave, or HyperLynx.
• Experience with isolation and grounding, failure mode effects analysis, fault tolerant design, and thermal management of power electronics.
• Experience designing and testing power electronics units to meet industry standards and requirements in the automotive, industrial, aircraft, or military markets (e.g., FCC, CISPR, UL safety standards, ECSS, NASA, MIL standards).
• Excellent written and verbal communication skills.

Preferred Experience

• Experience designing and testing isolated and non-isolated DC-DC power converters (e.g. discrete linear regulators, Buck, Boost, Buck-boost, Flyback, Forward).
• Experience designing or specifying custom power magnetics for power supplies and power line filters.
• Knowledge of power stage design and control methods for power factor correction (PFC) converters and active rectifiers.
• Experience generating statements of work and requirements for external vendors, vendor selection, and vendor management for power supply and power system rack developments.
• Experience with electronics schematic capture and printed circuit board (PCB) layout tools such as Altium, OrCAD, Allegro, or Xpedition.
• Experience running board-level power integrity simulation using tools such as ANSYS SiWave or HyperLynx.
• Knowledge of soft switching and resonant power converter topologies (e.g. LLC, CLLC, series resonant, phase shifted full bridge, dual active bridge).
• Programming skills to support hardware test and data processing (Python, MATLAB, etc.).

Compensation and Benefits

Full-time employment offers include company stock options and a generous benefits package including health, dental, vision, HSA, FSA, life, disability, and retirement plans.